|
Post by Kevin on Aug 24, 2005 21:36:43 GMT -5
how should i break in my new motor?...its a .26? Please give me specific instructions, im retarded when it comes to break in
|
|
|
Post by Ryan on Aug 24, 2005 22:02:01 GMT -5
u would break it in the exact way the instructions says. it should tell u to set the needles to sertain spots and run a few tanks. breakin a .26 motor is the same way as a .12 or a .18. just look in the manual
|
|
|
Post by Kevin on Aug 24, 2005 22:42:11 GMT -5
i didnt see it in there........ suggestions???
|
|
|
Post by Kevin on Aug 24, 2005 22:48:22 GMT -5
nvm i found it online thanks anyway
|
|
|
Post by UberRacer on Aug 25, 2005 6:13:13 GMT -5
|
|
|
Post by Scott on Aug 25, 2005 7:30:15 GMT -5
LOL
|
|
|
Post by Kevin on Aug 25, 2005 13:22:51 GMT -5
all done!....itts faster than my revo and its only running @ 195 degrees. Im gonna tune it up tomorrow and whoop ass on saturday
|
|
|
Post by UberRacer on Aug 25, 2005 14:49:48 GMT -5
I thought you were going to finish with the Revo, afraid your going to get beat?
|
|
|
Post by Kevin on Aug 25, 2005 18:17:09 GMT -5
nah its just the reason i was gonna finish w/ the revo is because i was scared the lsp would break, but after running today and whoping the mammoth st's and my set up still stock, o yeh its ass whooping time. Oh and to be honest it would be hard to hang with those guys with my revo.
|
|
|
Post by BrianMiskolczi on Aug 25, 2005 20:00:42 GMT -5
Uh oh, so you guys went out there today and practiced? Thats cool, so Kevin how u likin the truck?
|
|
|
Post by Kevin on Aug 25, 2005 21:34:50 GMT -5
im loving it right now but it needs a decent setup in order to get consistent runs like the revo, its still up in the air about which one i will run. i was definetly putting the smacketh down on ever one today and i was being gentle, i completely took of the front breaks and it handle much better now but i need to stiffen it up so the rear doesnt slide as much. what springs are you running on your buggy and what oil?
|
|
|
Post by kc Guy on Aug 27, 2005 10:32:33 GMT -5
Kevin I think we run the same, 70 in front and 40 in the rear with Kyosho blue springs all the way around. I think dougs has a set of blue springs in stock. hey congrats to you and Brian for going to hobbyhut and doing well. Hopefully see you guys soon
|
|
|
Post by Kevin on Aug 27, 2005 16:57:26 GMT -5
yeh, thanks, i put 60-40 and it was absolutely dialed i will prolly get those springs but man i was consistently putting down 21 sec laps...
|
|
|
Post by Ryan on Aug 27, 2005 17:31:29 GMT -5
yea man u were doin good today. i would just leave the truck the way it is. u need to work on the motor issue tho. it needs to idle for at least a little bit b4 it shuts off. ur truck would have shut off n e wayz in the pits cuz i would have stopped u n e how to fuel it up.
|
|
|
Post by BrianMiskolczi on Aug 28, 2005 9:04:16 GMT -5
Ya just turn the idle screw in a little bit to turn up the idle Kevin, if that doesnt work then its just too rich on the bottom end.
|
|